Rod Storage Ideas - Garage Door and Wall Mount - Share Yours

[fishnislife]

While messing around in the garage doing my boat modifications (http://www.northwestfishingreports.com/ ... 20&t=20980" onclick="window.open(this.href);return false;) I noticed that I needed a good rod storage set-up. To utilize the most space I thought of how I could attach to the garage door and still have the rods stay put. Well, after a little bit of thinking, cutting and an hour later.....this is what I came up with.



It is a 2x4 cut to fit the inside of one garage door panel. I hole saw cut, 4- 3/4" holes and used a speed square to mark out 45 degree angles down to each hole. This would allow the rods to roll as the garage door opened and not fall out when in the up position. Clean and completely out of the way. I could only comfortably fit 4 rods in the space I had. If I wanted, I could make another set and off set them a little lower in the next panel. To mount them I drilled through the inside of the support with 3 screws.



I also added a wall rod storage to take up space and add decoration to the garage. I used the same concept as above but only did 3 holes.




Each was sanded and all corners rounded.


Not sure if I will paint, stain or just keep the raw look.
I will take a garage door up picture when it is light out.

Share your rod storage?


fishnislife

[Larry3215]

Nice! Much better than my setup - piled in the corner!

[rseas]

Great post and you did a nice job with the garage door racks.

Although I will admit that I still have longer than 9' rods leaning in various corners of my garage and office the bulk of my rods call these milk crates home. When I lived in SoCal (I grew up in the PNW and live here now) I was always looking for another buck. Once a month I would rent an outdoor swap meet space and set up "7Seas Enterprises". I sold plastic swim bait kits, assorted other stuff and these milk crate rod racks. Although the ones I sold were custom 7Seas Enterprises branded anybody can make one. Materials are readily available; a milk crate and a bunch of PVC or ABS plastic plumbing. Using a table saw cut the required number of plastic plumbing tubes to length (in this case 63 per crate) and just load the crate up with them. Easy-peasy and safe storage for our beloved rods.

[fishnislife]

Nice idea rseas. I like it. That is simple and easy.

Thanks for sharing another cool way to store rods.


fishnislife

[Gringo Pescador]

Dude, that garage idea is awesome! You can see some of my rod storage in the how-to videos Mike & I did out of my garage but that space is full up. You just gave me my next project

[fishnislife]

You just gave me my next project

Sweet!
Let's see the final product when your done.
I'm gunna go check out the how-to video.



fishnislife

[fishnislife]

Can't find the video you speak of gringo. Can you post a link?






fishnislife

[Mike Carey]

Jerimiah, your garage door idea is brilliant! Here's that link:

[sickbayer]

I have mine on the garage door IMO best place for them when at home.

[Gringo Pescador]

Can't find the video you speak of gringo. Can you post a link?

fishnislife

Guess it doesn't show as well as I thought. I've got a 10' ceiling in my garage so I was able to make a vertical rod rack that holds 20 rods along the wall. On the bottom/base I put a 16" deep shelf and it is high enough I can fit milk crates (and other stuff) under it for more storage (wader boots, backpacks, tents, etc.).

Hanging just in front of the rod rack and below the ceiling about 4" I installed a heavy duty clothes rod holder and spanned a pipe across it. I then took a 4' 1x2 and screwed a hook in the side of one end. With this I can hang my fishing clothes (Summer & Winter waders, hip boots, rain jackets vests, etc.) on the hook, then lift them up to hang on the rod. This keeps the waders hung up to dry and still out the way. You can see the bottoms of my summer and neoprene waders behind Mike in the video

I will try to remember to take pics tonight and post them up.

[Gringo Pescador]

ok, so here's my setup to date - and it has served me well for awhile now.

IMG_3861.JPG (50.92 KiB) Viewed 31821 times

For the rod holders I just ripped a few lengths of cedar fenceboard. For the bottom I took a 2" doorknob hole cutter and made the holes, then laid that piece on another solid piece.

IMG_3862.JPG (52.25 KiB) Viewed 31821 times

For the tops, drilled holes, used a jig saw to cut back to the holes to complete the "U" shape, then tabs from a Costco milk jug and nailed them to the opening (had to double the tabs to make em stiff enough).

IMG_3863.JPG (41.24 KiB) Viewed 31821 times

This is the hook on the end of my stick to hang the waders & stuff

IMG_3860.JPG (41.69 KiB) Viewed 31821 times

I also added a pic of a setup I use to easily hang hip waders upside down.

IMG_3859.JPG (43.82 KiB) Viewed 31821 times

[Gringo Pescador]

What the hell?? All of my pics ended up upside down or sideway

Sorry guys. I got a new laptop - windows 10, I need to figure out what the heck I'm doing here They looked good going from my iPhone to my laptop but then flipped when they uploaded to here. I'll try to fix it when I get a chance

Oh well, in the mean time flip your screen or stand on your head and check it out

[Bodofish]

Just how the heck do you get those waders to stand right up like that?!?!?!

[Gringo Pescador]

What the hell?? All of my pics ended up upside down or sideway

Sorry guys. I got a new laptop - windows 10, I need to figure out what the heck I'm doing here They looked good going from my iPhone to my laptop but then flipped when they uploaded to here. I'll try to fix it when I get a chance

Oh well, in the mean time flip your screen or stand on your head and check it out

Fixed it

[Toni]

I don't have a garage so my room is the place where storage occurs. I had some one say it was art.

[demetriualston]

Hey, fishnislife I liked your wall mount. Share some more pictures.